ver : a_0 update : 2014.04.25 dc-dc brick pol10/16 series 10/16 a http://www.archcorp.com.tw tel: +886-2-26989508 fax: +886-2-26981319 -1- description pol series are high performance sip po l models, whose feature include wide range of input voltage, high power dens ity and perfect protection functions. this series include buck and boost models, the output current covering 10 a and 16a two levels. the output voltage can be set arbitrarily in the rating range. a ll models can be used in dpa or iba. this series which conform to the rohs6 requirement are suitable for telecom devices, server, network and industry devices power supply electrical specifications conditions: ta = -40 - 85c, vin = 4.5 - 5.5 / 3 - 5.5v / 10 - 14 vdc, vout = 3.3 / 0.75 ? 3.3 / 0.85 - 5 v dc, unless otherwis e notes. model no. pol10-05 pol16-05 pol16-12 voltage (v.dc.) (max.) (continuous) 6v 5.8v 16v operating voltage (v.dc.) 5v (4.5~5.5v) 3.3v (3~5.5v) 12v (10~14v) current (a) (max) 10a 23a 18a input no-load loss (w) (typ.) 0.3w 0.2w 0.7w voltage set point (v.dc.) (typ.) 3.3v 3.3v 1.2v voltage trim range (v.dc.) 3.2~3.4v 0.75~3.3v 0.85~5v current (a) (max.) 10a 16a 16a line regulation (ll-hl) (typ.) ? 1% load regulation (0-100%) (typ.) ? 1% ? 1.5% ? 2% ripple & noise (peak to peak) (typ.) (oscilloscope bandwidth:20 mhz) 70 mv 50 mv 3.3v:50 mv R 3.3v: 75 mv 0.9vout: 85% 0.85vout: 80% 1.0vout: 86% 1.0vout: 83% 1.2vout: 87.5% 1.2vout: 84% 1.5vout: 89.5% 1.5vout: 86% 1.8vout: 91% 1.8vout: 87.5% 2.5vout: 93% 2.5vout: 88% 3.3vout: 94.5% 3.3vout: 90.5% output efficiency (typ.) 95% 5.0vout: 92% over power protection hiccup mode over current protection hiccup mode over voltage protection 105~130% (self-recovery) 105~130% (self-recovery) short circuit protecti on (max.) hiccup mode threshold:125c / hysteresis:5c (typ.) protection over temperature protection self-recovery (the values are obtained by measuring the temperature of the pcb bottom near the thermal resistor.) operating temperature -40c?+85c storage temperature -55c?+125c temperature coefficient (max.) (ta = -40c to +85c (-40f to +185f )) 0.02 % vout / c 0.5 % vout / c 0.02 % vout / c humidity 95% rh environment mtbf 1.5 million hours (telcordia sr332; vin = 5 / 3.3 / 12 v; 80% load; airflow = 1.5 m/s (300 flm); ta = 40c (104f) dimension (l x w x h) tolerance ? 0.5 mm pol16-05: 2.0 x 0.5 x 0.33 inches ( 50.8 x 12.7 x 8.4 mm ) others: 2.0 x 0.55 x 0.47 inches ( 50.8 x 14.0 x 12.0 mm ) physical weight 6 g low level (v.dc.) -0.2~0.5v 0.4v (max.) -0.2~0.5v other remote on/off voltage high level (v.dc.) 2.0~5.0v 1.5~5.8v 2.0~5.0v key features ? input under voltage protection ? over current protection (hiccup mode) ? short circuit protection (hiccup mode) ? over voltage protection (self-recovery) * * ? over temperature protection (self-recovery) ? remote on/off control ? remote sense ? output voltage trim ? monotonic start-up into pre-biased outputs * ? meet ul94v-0 flammability requirements ? size: 2.0 x 0.5 x 0.33 inches (pol16-05) 2.0 x 0.55 x 0.47 inc hes (others model) ? 3-years product warranty *pol10-05 and pol16-12 without this function **pol16-05 without this function
ver : a_0 update : 2014.04.25 dc-dc brick pol10/16 series 10/16 a http://www.archcorp.com.tw tel: +886-2-26989508 fax: +886-2-26981319 -2- note derating 1. during the test of input reflected ripple current, the input terminal must be connected to a 12 uh inductor and a 220 uf ele ctrolytic capacitor. 2. point a, which is for testing the output voltage ripple, is 25 mm (0.98 in.) away from the vout pin. 3. the test platform is a 1oz four-layer board with the dimensions (l x w) being 100 mm x 50 mm (3.94 in. x 1.97 in.).
ver : a_0 update : 2014.04.25 dc-dc brick pol10/16 series 10/16 a http://www.archcorp.com.tw tel: +886-2-26989508 fax: +886-2-26981319 -3- mechanical dimension pin# single 1 dc out 2 dc out 3 sense 4 dc out 5 gnd 6 gnd 7 dc in 8 dc in 10 trim 11 on/off note 1. all dimensions in mm [in.] tolerances: x.x 0.5 mm [x.xx 0.02 in.] x.xx 0.25 mm [x.xxx 0.010 in.] 2. tolerances for the lengths, widths of a ll pins are x.xx 0.10 mm [x.xxx 0.004 in.]
|
